Sonance Speaker ThinLine TL623R User Manual

SONANCE THINLINE™  
IN-CEILING SPEAKERS  
INSTRUCTION MANUAL  
 
SONANCE THINLINE™ TL and SSTR  
INTRODUCTION  
Thank you for purchasing Sonance ThinLine™ TL and SSTR-series speakers.When properly installed  
your new speakers will give you years of entertainment pleasure. This manual will teach you all  
about your new speakers’ many innovative features and will show you how to get the very best  
performance from them. Please read it thoroughly.  
The directions in this manual apply to each model in the series. This manual covers the  
following speaker models: TL623R, TL622R; TL621R; TL623SSTR.  
F i g u r e 1 : S o n a n c e T h i n L i n e ™  
T L - S e r i e s S p e a k e r ( l e f t ) ;  
S S T R - S e r i e s S p e a k e r ( r i g h t )  
SAFETY WARNING:  
®
These speakers have FastMount tabs that prevent the speaker from falling out of the  
mounting hole during the installation process.  
The edges of the FastMount tabs are very sharp.  
Use caution when handling the speaker.  
See Installation (page 8) for complete information about the FastMount tabs.  
DESIGN AND FEATURES  
Thin (77mm) depth allows installation in areas too shallow for conventional in-ceiling speakers.  
• Pivoting tweeters direct the sound at listeners for clear sound and improved stereo imaging even when speaker placement options  
are limited.  
TL623SSTR reproduces both left and right channels from a single speaker — ideal for small spaces like hallways,closets and bathrooms.  
• A 3-position tweeter adjustment switch lets you balance the speaker’s high-frequency energy to better compliment your room’s  
setup and acoustics (TL623R/TL623SSTR).  
®
The RotoLock mounting system makes installation quick and easy.  
The detachable mounting flange expands installation options,allowing the speaker assembly to be easily mounted in custom cabinetry.  
BOX CONTENTS  
Your Sonance ThinLine speaker box should contain the following items:  
ThinLineTL623R/TL622R/TL621R:  
ThinLineTL623SSTR:  
(1) ThinLine TL623SSTR speaker  
(1) Paintable grille  
(2) ThinLine TL623R, TL622R or TL621R speakers  
(2) Paintable grilles  
(1) Plastic paint plug (installed on fronts of speakers)  
(1) Mounting cutout template (in packaging)  
(2) Plastic paint plugs (installed on fronts of speakers)  
(1) Mounting cutout template (in packaging)  
3
 
SONANCE THINLINE™ TL and SSTR  
OPTIONAL ACCESSORIES  
Symphony FlexBracket (part #92337): Plastic template to reserve a mounting hole for ThinLine speakers in new construction. Designed to be used  
®
with the RotoLock mounting system.  
SymphonyTR Coverplate (part #92335): Reusable cover protects the hole made by the FlexBracket during construction until the speaker is installed.  
®
Sonafill In-Ceiling System (part #91928): Retrofittable acoustical treatment consisting of two pillows and four tiles that virtually eliminates noises  
produced by resonating drywall. Dramatically improves midbass sound quality and reduces sound transmission into adjacent rooms.  
SPEAKER PLACEMENT  
TL623SSTR  
®
ThinLine Single Stereo Technology SSTR speakers are ideal for use in hallways, bathrooms, closets, or in any location where listeners will be moving around  
and a pair of stereo speakers would be impractical. The location of the speaker should be determined by considering the primary listening location as well  
as aesthetic values. Because a single ThinLine SSTR speaker reproduces both stereo channels from a single location, it will deliver outstanding performance  
from an extremely wide variety of mounting locations. For optimum results contact your Authorized Sonance Dealer for advice.  
TL623R, TL622R, TL621R  
When selecting mounting locations for your speakers you should consider such things as your primary listening location, the primary use for the speakers  
(distributed audio, 2-channel stereo or home theater) and aesthetic values. Your local authorized Sonance dealer is an expert in audio/video system  
planning and installation. We strongly recommend that you work with your dealer to ensure that your system is properly planned, assembled and installed.  
Distributed Audio Speaker Placement (Mono signal)  
All Sonance ThinLine speaker models have very smooth and predictable off-axis response, so they provide excellent coverage in distributed audio systems from  
a wide variety of installation locations. The chart in Figure 1 shows how far apart the speakers can be placed at different ceiling heights while still  
providing good coverage (as shown in Figure 2). The distances are based on ear heights of 62” for standing listeners and 40” for seated listeners.  
Speaker  
Spacing  
Speaker Spacing (in feet) for a Distributed Audio System  
Standing Listener Seated Listener  
8-foot ceiling  
10-foot ceiling  
12-foot ceiling  
14-foot ceiling  
5.7'  
9.7'  
9.5'  
Coverage  
Area  
Coverage  
Area  
13.5'  
17.5'  
21.5'  
13.7'  
17.7'  
F i g u r e 1 : D i s t r i b u t e d A u d i o S p e a k e r S p a c i n g  
F i g u r e 2 : D i s t r i b u t e d A u d i o C o v e ra g e A r e a  
4
 
SONANCE THINLINE™ TL and SSTR  
Home Theater Speaker Placement  
Left, Center  
& Right  
Left & Right  
Surround  
Speakers  
Speakers  
Left, Center & Right Channels  
• Place the left, center and right speakers from 1 foot to 2 feet in  
front of the video screen, anywhere from 6 feet to 10 feet apart,  
with the center channel speaker as close to midway between the  
left and right speakers as possible.  
6'– 10'  
6' – 10'  
apart  
• The left & right speakers should be at least 2 feet away from the  
side walls.  
TV  
apart  
• The main listening position should be between 4 and 10 feet away  
from the speakers.  
2' – 6'  
1'– 2'  
• In some cases pivoting the woofer of each speaker towards the  
listening position will help maximize the soundstage, especially  
when listening to stereo music sources.  
>2’  
Use Figure 3 as a guide.  
F igure 3: 5. 1 - Channel H om e Theater S peaker P lac em ent  
Left & Right Surround Channels (5.1-Channel System)  
Locate the left and right surround speakers on the ceiling between 2 feet and 6 feet behind the listening position. The speakers should be between 6 feet  
and 10 feet apart. Since the surround speakers are usually called-upon to create diffuse effects like the sound of wind or rain you can mount them close  
to walls without adversely affecting sound quality.  
• You can create a more diffuse, spacious surround effect by pivoting the tweeters towards a wall or window, away from the listeners.  
Use Figure 3 as a guide.  
Left & Right Surround and Surround Back Channels  
(7.1-Channel System)  
Left, Center  
& Right  
Left & Right  
Surround Speakers  
Speakers  
Surround  
Back  
• Left & Right Surround Speakers: Place the left and right  
surround speakers directly to the sides of the listening position,  
between 6 feet and 10 feet apart. The speakers can be placed close  
to the side walls.  
Speakers  
6'– 10'  
3' – 6'  
apart  
• Surround Back Speakers: Place the surround back speakers  
between 2 feet and 6 feet behind the listening position. The  
surround back speakers should be closer together than the left and  
right surround speakers — between 3 feet and 6 feet apart. Like  
the left and right surround speakers, the surround back speakers can  
be located close to walls without adversely affecting sound quality.  
TV  
apart  
2' – 6'  
1'– 2'  
>2’  
• You can create a more diffuse, spacious surround effect by pivoting  
the tweeters towards a wall or window, away from the listeners.  
F igure 4 : 7 . 1 - Channel H om e Theater S peaker P lac em ent  
Use Figure 4 as a guide.  
5
 
SONANCE THINLINE™ TL and SSTR  
Stereo (2-Channel)  
• Place the left and right speakers anywhere from 6 feet to 10 feet apart, with the main listening position as close to midway between the speakers as  
possible.  
• The speakers should be at least 2 feet away from the side walls.  
• The main listening position should be between 4 and 10 feet away from the speakers.  
• In most cases pivoting the tweeter of each speaker directly towards the main listening position will help maximize the stereo soundstage.  
Use the left and right speaker placement in Figures 3 and 4 as a guide.  
SELECTING THE PROPER SPEAKER WIRE  
For the best sound we recommend that you use premium Sonance  
®
MediaLinQ speaker cable, which also complies with UL fire rating codes.  
You may also experiment with audiophile brands of speaker cable and  
interconnects, but be sure to check local codes governing wire that may  
be installed within walls or ceilings. Different brands of wire can have  
different sonic characteristics, and some may be more compatible with the  
sonic “signature” of your various audio system components.  
Wire resistance in Ohms vs. length of cable run  
Distance in Feet 50' 100' 150' 200' 250' 300'  
20 gauge  
18 gauge  
16 gauge  
14 gauge  
12 gauge  
10 gauge  
1.04 2.07 3.11 4.14 5.18 6.22  
.65 1.30 1.96 2.61 3.26 3.91  
.41 .82 1.22 1.63 2.04 2.45  
.26 .52 .77 1.03 1.29 1.55  
.16 .32 .49 .65 .81 .97  
.10 .20 .31 .41 .51 .61  
For the best sound you should never use thin-gauge speaker wire – it will  
constrict the sound and diminish bass response. Extra resistance in the  
speaker wire can make a speaker sound less dynamic and reduce  
definition of the bass frequencies. In extreme cases, it can even attenuate  
high frequencies. Also, amplifier power is wasted in thin wire with extra  
resistance, reducing your system’s maximum output level. To prevent  
degrading sound quality, the total wire resistance should be less than 10%  
of the speaker’s impedance. This means that for an 8-ohm speaker, the  
F i g u r e 5 : S p e a k e r W i r e R e s i s t a n c e T a b l e  
total resistance of the wire should be less than 0.8 ohms. Refer to Figure 5 when selecting the proper wire gauge for your system.  
PREPARING THE INSTALLATION LOCATION  
Building a Back Box into the Ceiling Bay  
Sonance ThinLine speakers are designed to provide exceptionally musical performance in a wide variety of enclosure volumes. You can get the very best  
performance from your speakers by partitioning a section of the ceiling bay to form a sealed back box with a specific internal volume. Building such an  
enclosure will create a dramatic improvement in your speakers’ bass performance and power handling.  
Ideal back box volume requirements:  
ThinLine TL623R:  
ThinLine TL622R:  
1.5 ft3  
1.2 ft3  
ThinLine TL621R:  
ThinLine TL623SSTR: 1.5 ft3  
1.0 ft3  
6
 
SONANCE THINLINE™ TL and SSTR  
Insulating the Ceiling Cavity  
You can also reduce sound transmission to adjacent rooms and improve speaker performance by inserting a sheet of unfaced fiberglass insulation over the  
back of the speaker. To reduce mechanical noise produced by unsupported drywall, install fiberglass insulation in the ceiling bays adjacent to the speaker  
location.  
®
Sonafill  
Sonafill (part #91928) is a retrofittable acoustical treatment system consisting of two pillows and four tiles that virtually eliminates noises produced by  
resonating drywall. The tiles have pressure-sensitive adhesive and are installed on the back of the drywall on either side of the speaker between the  
ceiling joists; the pillows are then stuffed in place behind the tiles. The system dramatically improves midbass sound quality and reduces sound transmis-  
sion into adjacent rooms.  
INSTALLING THE SPEAKERS  
Before Installation: New Construction  
For installations in new construction, Sonance recommends using a Symphony FlexBracket (part #92337) to reserve a location for the speaker. The  
FlexBracket has perforated wings that can be positioned at any angle around the bracket, and is nailed or screwed to the studs. This serves as a guide  
for the drywaller so that the speaker hole will be in the desired location once the drywall is installed.  
Before Installation: Retrofit  
1. Determine the location for the speaker (see Speaker Placement on page 4).  
2. Perform an obstruction survey to be certain that there are no studs, conduit, pipes, heating ducts or air returns in the ceiling cavity that will interfere  
with the speaker.  
3. The cutout for all ThinLine speakers is 85/32” (207mm). There also must be at least 31/32” (77mm) depth within the ceiling cavity.  
4. Position the included cutout template where the speaker is to be located and pencil an outline on the ceiling.  
• If you are unsure about obstructions, drill a small hole in the center of the outline and insert a coat hanger wire into the hole to feel-around for  
possible obstructions.  
5. Cut the mounting hole using a drywall saw, and run the speaker wires from the mounting hole to the amplifier location.  
• Consult local building codes before running speaker wires through walls.  
Installation  
®
®
Sonance ThinLine speakers feature exclusive FastMount tabs and an integral RotoLock mounting system for quick mounting directly into existing ceilings  
and walls.  
WARNING:The edges of FastMount tabs are very sharp. Use caution when handling the speaker.  
1. Remove the paint plug from the speaker.  
2. Run speaker wire from the amplifier location to each speaker.  
3. Strip ¼” – ½” of insulation from each speaker lead. Twist the strands or tin the exposed wire with solder to ensure that there are no stray strands.  
7
 
SONANCE THINLINE™ TL and SSTR  
(Stray strands that touch each other can cause a short-circuit that can damage your  
amplifier.)  
4. The speaker’s connector posts are spring-loaded. Push the top of each connector post  
down to open the connector and insert the exposed wires into the holes in the posts.  
(The TL623SSTR has connectors for both the left and right channels.)  
• The speaker’s positive post is labeled with a red dot; the negative post is labeled with  
a black dot. Double-check that you connected amplifier “+” to speaker “+” and  
amplifier “–” to speaker “–”.  
5. Make sure all the RotoLock clamps are in the full clockwise position so that they are  
tucked within the mounting hole’s border. Insert the speaker into the hole in the  
ceiling (Figure 6). The RotoLock system can accommodate a maximum ceiling material  
thickness of 1¼”.  
F i g u r e 6 : I n s e r t S p e a k e r  
I n t o M o u n t i n g H o l e  
• The FastMount tabs will prevent the speaker from falling out of the mounting hole, allowing  
the installer to let go of the speaker to pick-up tools or other items (Figure 7).  
NOTE: THE FASTMOUNT TABS ARE DESIGNED FOR ONE-TIME USE ONLY. IF THE  
SPEAKER IS REMOVED FROM THE MOUNTING HOLE THE FASTMOUNT TABS WILL  
DISCONNECT AND REMAIN INSIDE THE CEILING.  
FastMount®  
Tabs  
6. Tighten the four screws on the front of the speaker baffle. The RotoLock clamps will  
automatically rotate into position and begin clamping the speaker (Figure 8).  
• When you notice resistance on the screws the speaker has been clamped successfully.  
NOTE: THE SPEAKER FLANGE IS DESIGNED TO FLEX AND CONFORM TO ANY SMALL  
IMPERFECTIONS IN THE CEILING SURFACE. DO NOT TIGHTEN THE SCREWS SO  
MUCH SO THAT THE FLANGE BOWS-OUT.  
IMPORTANT: Always u s e l o w - t o r q u e s e t t i n g s ; N E V E R  
over-tighten.  
F i g u r e 7 :  
F a s t M o u n t ® T a b s  
7. Attach the grille after the speaker has been installed. Insert about half of the grille into  
the groove at the edge of the speaker. Gently fit the remaining half of the grille by work-  
ing around the speaker, fitting the grille into the groove as you go.  
RotoLock®  
Clamps  
NOTE: YOU CAN ADJUST THE TORQUE APPLIED TO THE ROTOLOCK SCREWS TO  
ACHIEVE A PROPER GRILLE FIT.  
F i g u r e 8 :  
R o t o L o c k ® C l a m p s  
8
 
SONANCE THINLINE™ TL and SSTR  
PAINTING THE SPEAKERS AND GRILLES  
You can paint the speakers and grilles before installing them, which will eliminate the “paint scar” that can be left on the ceiling if the speaker ever needs  
to be removed for service. You can also paint the speakers after installation, but before the grilles are attached. All Sonance ThinLine speakers come from  
the factory fitted with a plastic ‘paint plug’ that protects the speaker drivers while the mounting flange is being painted.  
Sonance always suggests painting the grille separately from the speaker. Before painting, carefully remove the under-grille cloth. It is held in place with a  
light tacking glue that makes it easy to remove.  
Spray the grilles with thinned paint (5 parts thinner to 1 part paint), being careful not to plug the holes. Too heavy a coat of paint on the grille will  
adversely affect the sound of the speaker.  
Once the grilles and flange are painted and dry, replace the under-grille cloth, remove the paint plug from the mounting flange and install the grille.  
SPEAKER ADJUSTMENTS  
Pivoting Tweeter  
ThinLine TL623R and TL622R have a pivoting tweeter. This lets you direct sound toward or away from the listening area,  
depending on how the speakers are being used:  
• If you’re using the speakers in stereo or as the front left/center/right speakers in a home theater, pivot the tweeter  
directly towards the listening area. This will help the sound from the speakers blend into a solid soundstage even if  
the speakers are widely separated.  
• If you’re using the speakers as surround channel speakers in a home theater, you can create a more diffuse, spacious  
surround effect by pivoting the tweeters towards a wall or window, away from the listeners.  
F i g u r e 9 :  
P i v o t i n g t h e Tw e e t e r  
To Pivot theTweeter:  
Apply light pressure to the plastic ring around the outside edge of the tweeter dome, as shown in Figure 9. Do not  
touch or apply pressure to the tweeter dome.  
Tweeter Level Control  
The ThinLine TL623R and TL623SSTR have a tweeter level control switch (see Figure 10) that lets you boost or cut the tweet-  
er’s level by 3dB. This allows you to adjust the speaker’s brightness to better match your listening room or personal taste.  
Tweeter  
Level Control  
Once you have installed the speakers, listen to a variety of music that you are familiar with. If the music all tends to  
sound too bright or dull, use the Tweeter Level Control to compensate. If some recordings sound dull and some sound bright  
the speaker is accurately reproducing differences in the recordings, and you should leave the control in the middle (0dB)  
position.  
F i g u r e 1 0 :  
Tw e e t e r L e v e l  
C o n t r o l  
9
 
SONANCE THINLINE™ TL and SSTR  
SPECIFICATIONS  
TL623SSTR  
Tweeter:  
Woofer:  
TL623R  
Two 1" (25mm) Silk domes, Ferrofluid-cooled  
6½" (165mm) Carbon fiber cone, rubber surround, dual  
voice coil  
Tweeter:  
1" (25mm) Silk dome, Ferrofluid-cooled, pivoting  
Woofer:  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
6½" (165mm) Carbon fiber cone, rubber surround  
43Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 135 Watts maximum  
90dB SPL (2.83V 1 meter)  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
Grille Material:  
Adjustments:  
Dimensions (Dia. x Depth): 9¾" (248mm) x 31/32" (77mm)  
Cutout Diameter:  
Shipping Weight:  
43Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 135 Watts maximum  
90dB SPL (2.83V 1 meter)  
Perforated aluminum  
Grille Material:  
Adjustments:  
Perforated aluminum  
±3dB Tweeter level  
±3dB Tweeter level  
Dimensions (Dia. x Depth): 9¾" (248mm) x 31/32" (77mm)  
Cutout Diameter:  
Shipping Weight:  
85/32" (207mm)  
10 lbs. (4.5kg) Pair  
85/32" (207mm)  
5 lbs. (2.3kg) Each  
TL622R  
Tweeter:  
Woofer:  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
1" (25mm) Silk dome, Ferrofluid-cooled, pivoting  
6½" (165mm) Polypropylene cone, rubber surround  
45Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 125 Watts maximum  
89dB SPL (2.83V 1 meter)  
Grille Material:  
Adjustments:  
Perforated aluminum  
None  
Dimensions (Dia. x Depth): 9¾" (248mm) x 31/32" (77mm)  
Cutout Diameter:  
Shipping Weight:  
85/32" (207mm)  
10 lbs. (4.5kg) Pair  
TL621R  
Tweeter:  
Woofer:  
Frequency Response:  
Impedance:  
Power Handling:  
Sensitivity:  
¾" (19mm) Silk dome, Ferrofluid-cooled  
6½" (165mm) Polypropylene cone, rubber surround  
50Hz – 20kHz ±3dB  
8 Ohms nominal; 6 Ohms minimum  
5 watts minimum; 100 Watts maximum  
88dB SPL (2.83V 1 meter)  
Grille Material:  
Adjustments:  
Perforated aluminum  
None  
Dimensions (Dia. x Depth): 9¾" (248mm) x 31/32" (77mm)  
Cutout Diameter:  
Shipping Weight:  
85/32" (207mm)  
9 lbs. (4.1kg) Pair  
10  
 
SONANCE THINLINE™ TL and SSTR  
TECHNICAL ASSISTANCE AND SERVICE  
If you any have questions about the operation or installation of this product, please call our Technical Assistance  
Department on any business day at (800) 582-0772 or (949) 492-7777; from 7 a.m. to 5 p.m., PST.  
If your speakers should need repair or service, contact your Sonance Authorized Dealer for help, or use the following procedure:  
1. Prior to calling, note the product’s model number, serial number, purchase date, and the name and address of the dealer where you purchased the product.  
2. Contact our Technical Assistance Department at the above number(s) and describe the problem the unit is experiencing. If applicable, they will issue a  
Return Authorization Number.  
IMPORTANT: YOU MUST HAVE PRIOR AUTHORIZATION TO RETURN YOUR SPEAKER TO SONANCE!  
3. If you’re directed to return the unit to Sonance for repair, pack the unit in its original shipping carton. If needed, you can obtain replacement packag-  
ing from us for a small charge. Note: it is best if you place the box into an additional outer “overcarton” before shipment to minimize a chance of  
theft in shipment. Please include a copy of the original bill of sale inside the package.  
4. Contact a package delivery company such as United Parcel Service or Federal Express to arrange prepaid (not collect) shipping. Do not use the U.S. Postal  
Service.  
IMPORTANT: Freight collect shipments will be refused.  
5. Write the Return Authorization Number on the outside of the shipping carton.  
6. Ship the packaged unit to:  
QUALITY ASSURANCE DEPARTMENT  
SONANCE  
212 AVENIDA FABRICANTE  
SAN CLEMENTE, CA 92672-7531  
11  
 
SONANCE THINLINE™ TL and SSTR  
LIMITED LIFETIME WARRANTY COVERAGE (U.S. ONLY)  
SONANCE WARRANTS TO THE ORIGINAL RETAIL PURCHASER ONLY THAT THIS SONANCE PRODUCT WILL BE FREE FROM DEFECTS IN MATERIALS  
AND WORKMANSHIP, PROVIDED THE SPEAKER WAS PURCHASED FROM A SONANCE AUTHORIZED DEALER.  
Defective products must be shipped, together with proof of purchase, prepaid insured to the Authorized Sonance Dealer from whom they were purchased, or  
to the Sonance factory at the address listed on this instruction manual. Freight collect shipments will be refused. It is preferable to ship this product in  
the original shipping container to lessen the chance of transit damage. In any case, the risk or loss or damage in transit is to be borne by the purchas-  
er. If upon examination at the factory or Authorized Sonance Dealer it is determined that the unit was defective in materials or workmanship at any time  
during this warranty period, Sonance or the Authorized Sonance Dealer will, at its option, repair or replace this product at no additional charge, except as  
set forth below. If this model is no longer available and can not be repaired effectively, Sonance, at is sole option, may replace the unit with a current  
model of equal or grater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If mounting  
surface modification is required, Sonance assumes no responsibility or liability for such modification. All replaced parts and product become the property of  
Sonance. Products replaced or repaired under this warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.  
This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping  
procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has not  
been authorized or approved by Sonance. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This Warranty will  
be void if the Serial Number on the product has been removed, tampered-with or defaced. This Warranty is in lieu of all other expressed warranties. If the  
product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no  
event will Sonance be liable for any incidental or consequential damages arising out of the use or inability to use the product, even if Sonance or an  
Authorized Sonance Dealer has been advised of the possibility of such damages, or for any claim by any other party.  
Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply. All implied warranties  
on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation on the length of an implied warranty. If the  
original retail purchaser resides in such a state, this limitation does not apply.  
EXCLUSIONS AND LIMITATIONS  
The warranty set forth above is in lieu of all other warranties, express or implied, of merchantability, fitness for a particular purpose, or otherwise. The  
warranty is limited to Sonance products registered herein and specifically excludes any damage to loudspeakers and other allied or  
associated equipment which may result for any reason from use with this product. Sonance shall, in no event, be liable for incidental or consequential  
damages arising from any breach of this warranty or otherwise. This warranty gives you specific legal rights, and you may have other rights which vary  
from state to state.  
12  
 
SONANCE THINLINE™ TL and SSTR  
SYSTEM NOTES:  
13  
 
SONANCE THINLINE™ TL and SSTR  
SYSTEM NOTES:  
14  
 
 
©2006 Sonance. All rights reserved. Sonance, Sonance ThinLine, RotoLock, Sonafill and FastMount are trademarks or registered trademarks of Dana Innovations.  
Due to continuous product improvement, all features and specifications are subject to change without notice. For the latest Sonance product specification information visit our website:  
212 Avenida Fabricante • San Clemente, CA 92672-7531 USA • (800) 582-7777 or (949) 492-7777 • FAX: (949) 361-5151 • Technical Support: (800) 582-0772  
33-4379  
07/06  
 

Smooth Fitness Car Video System GMTV15 User Manual
Sony Bluetooth Headset Bluetooth Audio System User Manual
Sony CD Player NSX AJ700 User Manual
Sony Projection Television KF 42WE620 User Manual
Sony Robotics ERS 111 User Manual
Sony Universal Remote RM X302 User Manual
Southbend Lathe SB1046PF User Manual
Sub Zero Ventilation Hood PRO VENTILATION HOODS User Manual
SVAT Electronics Home Security System CV501 16CH User Manual
Sylvania VCR 6260VC User Manual